 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Fixed Voltage SLIC Protector Fixed Voltage SLIC Protector (T/R) (G) These DO-214AA unidirectional protectors are constructed with a SIDACtor device and an integrated diode. They protect SLICs (Subscriber Line Interface Circuits) from damage during transient voltage activity and enable line cards to meet various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA968 (formerly known as FCC Part 68). For specific design criteria, see details in Figure 3.23. Cathode Electrical Parameters Part Number * P0641S_ P0721S_ P0901S_ P1101S_ VDRM Volts 58 65 75 95 VS Volts 77 88 98 130 VT Volts 4 4 4 4 VF Volts 5 5 5 5 IDRM Amps 5 5 5 5 IS mAmps 800 800 800 800 IT Amps 1 1 1 1 IH mAmps 120 120 120 120 CO pF 70 70 70 70 * For individual "SA" and "SC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * VDRM is measured at IDRM. * VS and VF are measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. * Off-state capacitance is measured at 1 MHz with a 2 V bias and is a typical value for "SA" and "SB" product. "SC" capacitance is approximately 2x the listed value. * Parallel capacitive loads may affect electrical parameters. Surge Ratings (Preliminary Data) IPP 2x10 s Amps 150 500 IPP 8x20 s Amps 150 400 IPP 10x160 s Amps 90 200 IPP 10x560 s Amps 50 150 IPP 10x1000 s Amps 45 100 ITSM 60 Hz Amps 20 50 di/dt Amps/s 500 500 Series A C http://www.teccor.com +1 972-580-7777 2 - 52 (c) 2003 Teccor Electronics SIDACtor(R) Data Book and Design Guide Fixed Voltage SLIC Protector Thermal Considerations Package DO-214AA Symbol TJ TS RJA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value -40 to +150 -65 to +150 90 Unit C C C/W +I +I IPP - Peak Pulse Current - %IPP IT IS IH VT VF 100 Peak Value tr = rise time to peak value td = decay time to half value VS VDRM -V -V Waveform = tr x td IDRM VT IDRM IH IS IT -I +V +V 50 Half Value VDRM VS 0 0 tr td t - Time (s) -I V-I Characteristics tr x td Pulse Wave-form 14 Percent of VS Change - % 10 IH (TC = 25 C) 12 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 C 25 C Ratio of Case Temperature (TC) - C Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature Normalized DC Holding Current versus Case Temperature (c) 2003 Teccor Electronics SIDACtor(R) Data Book and Design Guide 2 - 53 http://www.teccor.com +1 972-580-7777 Data Sheets |
Price & Availability of P11013A
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |